Drip edge
Edge metal is renewed along the roof perimeter so water drips clear of the fascia.
Roof Repair
Flashing Repair Pequannock, NJ
A Pequannock roofer can stop leaks where the roof meets a wall, dormer, skylight or edge by renewing the flashing at that joint, so water is shed by the metal itself. Dial (862) 458-0110 to talk with a local roofer about the flashing.
Shingles handle the open field of a roof; flashing handles the joints. The main types are step flashing at sidewalls, apron flashing at headwalls, counter flashing over the top, kickouts at the bottom of walls, valley metal and drip edge at the edges. Each of those pieces has one job, and when it fails, water finds the gap.
Flashing problems often hide inside the wall rather than on the ceiling. A missing kickout is a classic example: water running down the roof edge pours behind the siding at the bottom of the wall, and the rot shows up later as soft trim, stained siding or a damp window below. Catching it early keeps the repair to the flashing instead of the wall.
Caulk is not flashing. Sealant smeared where flashing should be dries and cracks in a few seasons, and it can trap water instead of shedding it. Proper flashing sheds water by gravity and lapping, so it keeps working even after any sealant ages.
Depending on what the roofer finds, flashing repair in Pequannock, NJ can go hand in hand with chimney flashing repair and roof leak repair.
Dealing with this in Pequannock, NJ right now? Call (862) 458-0110 and describe the problem to a roofer who works in Pequannock.
Call nowThe process
What happens during a flashing repair
Here is how a roofer typically approaches a flashing repair.
Check the flashing
Each joint is examined for missing kickouts, loose step pieces and counter flashing that no longer covers the top. Soft siding or stained trim below the joint suggests the wall needs a look too.
Open the joint
The shingles next to the wall come up, and the lowest siding courses come off to expose the flashing. Working the new pieces in correctly depends on access behind the siding.
Replace the pieces
Each new step piece overlaps the one beneath it, and the kickout at the base sends water into the gutter. Fasteners go into the roof deck only, never through the vertical leg into the wall.
Seal the wall side
The weather barrier laps over the step flashing, and siding is reinstalled with clearance above the roof surface. The gap lets the joint dry and keeps trim from wicking water.
Seal the eaves
At the roof edges, drip edge is reset or replaced to protect the fascia and deck edge. The lap order differs at eaves and rakes, and getting it right matters.
What is included
Flashing a roofer can repair
Kickout flashing
Missing kickout diverters are installed at the base of sidewalls so runoff stops soaking the siding.
Counter flashing
Cap flashing on masonry is reset into the mortar joint where the wall and roof meet.
Apron flashing
Apron flashing where a roof slope meets a wall above is renewed so water cannot run behind it.
Step flashing
Loose or rusted step flashing is renewed so water stays on the roof.
Related service
Roof Flashing Repair Pequannock, NJ
Flashing repairs can be small or involved, depending on how long water has been getting in. Some repairs take an hour at one corner; others mean opening a whole wall joint and replacing the metal course by course. Ask the roofer which kind of repair your joint needs.
Material matters too. Aluminum is common and easy to form, galvanized steel is stiffer, and copper lasts a very long time; aluminum should not sit directly against fresh mortar or certain treated lumber, which can corrode it. Matching metals avoids corrosion where new and old flashing meet.
Related service
Roof Valley Flashing Pequannock, NJ
Roof valleys carry the runoff from two slopes, so they handle more water than any other part of the roof. An open valley uses a strip of metal, often a W-shaped valley pan with a center rib, with the shingles cut back on each side; a closed valley has the shingles woven or cut across it with no metal showing. A peel-and-stick underlayment down the valley is the backup layer in both styles.
Leaves and needles that pile up in a valley hold water and wear the shingles or rust the metal. Uncut shingle corners can catch water and direct it under the roofing. Valley repair usually means removing the shingles along the valley, replacing the membrane and metal and reshingling with the right cuts.
Local help
Flashing Repair Near Me
Around Pequannock, flashing leaks tend to show up wherever a roof runs into a wall, a dormer or a skylight. From Pequannock out to neighboring towns such as Pompton Plains, Lincoln Park, Towaco and Riverdale, older homes often have rusted or face-nailed flashing, while newer ones sometimes lack kickouts entirely, which is why roofers pay extra attention to walls, dormers and additions.
For flashing repair in Pequannock, NJ or nearby towns like Pompton Plains, Lincoln Park, Towaco and Riverdale, call (862) 458-0110 to reach a roofer who covers your street.
Roofs in this climate
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Pequannock, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why fix it now
Smaller repairs
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Local knowledge
Local roofers see the same roofs and storm damage across Pequannock and nearby towns.
Straight answers
Ask your questions before you agree to anything.
Flashing Repair questions
Why does flashing need to be woven with the shingles?
Along a sidewall, each shingle course gets its own small flashing piece that overlaps the one below. Because each piece laps the one below, water is passed down the wall joint from piece to piece and onto the roof. A single long strip of metal along a wall cannot do that and tends to channel water behind the shingles.
Why does my roof need kickout flashing?
It is a bent piece of flashing at the lower end of a sidewall joint. It throws runoff away from the wall and into the gutter. Without one, the wall below that joint often rots quietly for years.
Is it possible to fix flashing without a new roof?
Most flashing problems are fixed without touching the rest of the roof. The work stays local to the joint, with new shingles woven in along it. If the roof is near the end of its life, it can make sense to replace flashing as part of a reroof instead.
Will caulk fix leaking flashing?
Caulk can slow a flashing leak but almost never fixes it. Sun and temperature swings crack it, and water gets behind it again, sometimes trapped where it rots wood faster. The lasting fix is new flashing installed and lapped correctly.
What are the signs of bad roof flashing?
Water showing up near a wall joint, skylight or valley points to flashing. From outside, rusted, loose or caulked-over flashing is a warning sign. Soft or stained siding at the bottom of a sidewall often means a missing kickout. A roofer reached at (862) 458-0110 can look at every joint.
More questions? Call (862) 458-0110
Other services that may help
Chimney Flashing Repair
Fixing leaks around the chimney with new flashing set into the mortar joints, instead of another coat of tar.
Learn moreRoof Leak Repair
Stopping water at the pipe boots, flashing, valleys and nail holes where roofs actually leak, before wet decking and insulation turn into rot.
Learn moreSkylight Repair
Fixing leaking, fogged or cracked skylights and the flashing around them, without replacing a unit that can still be saved.
Learn moreRoof Vent Repair
Vent and pipe boot repairs for leaks, hail damage and worn-out parts, before a small crack soaks the attic.
Learn more
Looking for something else?
See all roofing servicesGet flashing repair help in Pequannock
Call (862) 458-0110 to talk to a roofer serving Pequannock, NJ.